Hotpoint HS MR 2A ZU B Instruction for Use download pdf (Page 10)

1010

2. The battery indicator (41) on the 4LEDs (39)

ashes during the charging time.

3. When the battery indicator (41) is not ashing, the

vacuum cleaner battery has been charged, pull out

the plug from mains and disconnect the charger in

the back of the main body and close the opening lid

for charging. Note the charging time should not be

more than 12 hours to avoid any damage to batteries.

USING THE VACUUM CLEANER

Do not use the vacuum cleaner without lters or dust

container, as the appliance could get damaged.

1. Place the suction selector on the brush position

(30) in the back main body (D).

2. Press start/stop button (37), the standby

indicator (40) and the battery indicator on the

4LEDs (41) are on, and to start the appliance

press the electronic power regulator (38).

3. The suction power is set on medium intensity by

default, to select the desired suction intensity (based

on the model) use the +/- button and electronically

adjust the power (23, 24) of the Remote Power

Control on the handle or manually push the

electronic power regulator (38) on the main body.

We suggest to use a low suction power on delicate

surfaces such as curtains, fabrics, cushions etc to

avoid any damage.

1. To pause the vacuum cleaner, if this feature is

available, you can use the standby button (22) on

the Remote Power Control (based on the model).

2. To switch off the appliance press the start/stop

button (37) again.

Using the motorized brush

When the product is not in the upright position, the

power suction and the rotating brush with the UV

light (if available) are working. To pause the vacuum

cleaner use the standby button (22) on the Remote

Power Control (21) and to restart the suction power

press the standby button or the electronic power

regulator.

When the product is in the park position, the

Start&Pause function switches off the operation of

the UV light (if available) and the rotating brush, while

the suction power in on. In this position it is possible

to use the other accessories in the clamp (17). To

pause the vacuum cleaner use the standby button

(22) on the Remote Power Control (21), and to restart

the suction power press the standby button or the

electronic power regulator.

In cases of using of vacuum cleaner by the handle (E)

This allows you to clean surfaces not accessible with

the motorized brush.

1. Place the suction selector on the accessory

position (29) in the back main body.

2. Fit the two-in-one accessory (25) into the handle

frame, pushing down the handle slide clamp (18).

3. To remove the handle, press the handle release

button (36) and pull it out.

4. Press start/stop button (37), the standby

indicator (40) and the battery indicator on the

4LEDs (41) are on, and to start the appliance

press the electronic power regulator (38).

FEATURES

Led indicators and Electronic power

regulator (38,39) (if available)

Standby indicator (40): when you use the standby

button (22) on the Remote Power Control, the suction

power stops and the power indicator (42) blinks one

time. To restart the suction power press the standby

button (22). The standby indicator is always on.

Battery indicator (41): When the product works the

battery indicator (41) is switch on and the light is xed,

while during charging time it ashes.

Power indicator (42): it blinks when you press a

button on the Remote Power Control.

Filter Cleaning Indicator (43): after several hours of

use, the led switch on. After cleaning the HEPA lter

(see chapter “Cleaning and maintenance”), to reset

the indicator press the symbol “+” (24) of Remote

Power Control some seconds.

Electronic power regulator (38): when press this

button on the main body the suction power works

cyclically (med -> max -> min -> med). It allows to set the

suction power required.

Remote Power Control

The Remote power control (21) (if available) enables

you to adjust the suction power directly and effortlessly

from the hand grip. When using the vacuum cleaner,

you can keep it on standby by pressing the Standby

button (22).

To insert or change the batteries of your Remote Power

Control:

1. Open the battery compartment (28).

2. Insert two AAA batteries, making sure of the

positive and negative poles.

3. Close the battery compartment until it clicks into

place and screw the cover.

Ultraviolet light

The UV light (if available) (4) is an ultraviolet steriliza-

tion function, when the brush is collecting dust on the

ground normally, the UV lamp is lighting, antiseptic

function is working. When the brush is not in contact

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Hotpoint HS MR 2A ZU B Instruction for Use Page 10

Comments to this Manuals

Related products and manuals for Unknown Hotpoint HS MR 2A ZU B