Hotpoint ITWD 61252 G (PL) Instruction for Use download pdf (Page 10)

EN 8

Recovering an object that falls between

the drumand the tub

If an object accidentally falls between the drum and

the tub, you can recover it thanks to one of the remov-

able drum blades:

1. Unplug the washing machine.

2. Remove the laundry from the drum.

3. Close the drum ﬂaps and turn the drum a

half-turn (picture 24).

4. Using a screw-driver, press on the plastic end

while sliding the blade from left to right (picture

25, 26).

5. It will fall into the drum.

6. Open the drum: you can recover the object

through the hole in the drum.

7. Reﬁt the blade from inside the drum: Position the

plastic tip above the hole on the right side of the

drum (picture 27).

8. Then slide the plastic blade from right to left until

it clips.

9. Close the drum ﬂaps again, turn the drum through

half a turn and check the positioning of the blade

at all its anchorage points.

10. Plug the washing machine in again.

REMAINING MOISTURE CONTENT OF THE LAUNDRY

AFTER SPINNING

The degree of moisture remaining in the laundry

after spinning mainly depends on the fabric type, the

selected programme and spin speed.

The lowest remaining moisture content can be

achieved using the wash programme referred to

by the Energy Label, with maximum spin speed.

This programme is marked in the separate

programme chart as “Reference programme

for the Energy Label”. Below a survey of the

remaining moisture content (in %) related to

the various spin-drying efﬁciency classes:

Spin-drying

efﬁciency class

Remaining moisture

content in %

A (= most efﬁcient) less than 45

B 45 or more, but less than 54

C 54 or more, but less than 63

D 63 or more, but less than 72

E 72 or more, but less than 81

TRANSPORT AND HANDLING (picture 30)

1. Unplug the washing machine.

2. Turn off the tap.

3. Remove the water supply and drain hose.

4. Eliminate all water from the hoses and the washing

machine (see “Cleaning the Filter/ Draining

Residual Water”). Wait for the water to cool so as to

avoid any accidents.

5. To facilitate moving the machine, pull the handle

situated at the bottom front (if available on your

model) out a little by hand and pull it out to the stop

with the foot. Afterwards push the handle back into

the original stable position.

6. Fix the transport bracket again for transportation.

7. Transport the washing machine upright.

IMPORTANT: Do not use the washing machine while

the handle is pulled out.

CLEANING THE FILTER/ DRAINING RESIDUAL WATER

The washing machine is provided with a self-cleaning

pump. The ﬁlter keeps objects like buttons, coins,

safetypins etc. which have been left in the laundry.

We recommend to check and clean the ﬁlter regularly,

at least two or three times a year.

Especially:

• if the appliance is not draining properly or if it fails

to perform spin cycles.

• if the “Pump” indication lights up.

IMPORTANT: make sure the water has cooled

before draining the appliance.

Residual water must be drained also before transport-

ing the machine.

1. Unplug the washing machine.

2. Open the ﬁlter cover with a coin (picture 28).

3. Place a bowl beneath it.

4. Turn the ﬁlter slowly anti-clockwise until some

water starts to ﬂow out; do not remove it as yet.

5. Wait until all the water has drained.

6. Now unscrew the ﬁlter completely and extract it

(picture 29).

7. Clean the ﬁlter and the ﬁlter chamber.

8. Make sure the pump impeller (in the housing

behind the ﬁlter) is not obstructed.

9. Insert the ﬁlter again and screw it in

completely in clockwise direction. Make

sure the ﬁlter is screwed in properly, as far

as it will go.

10. Pour approximately one litre of water into the

washing machine via the drum and check that

water does not leak from the ﬁlter.

11. Close the ﬁlter cover.

12. Reconnect the washing machine.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 35 36

Comments to this Manuals

No comments

Hotpoint ITWD 61252 G (PL) Instruction for Use Page 10

Comments to this Manuals

Related products and manuals for Washing machines Hotpoint ITWD 61252 G (PL)